Powder Bed Fusion Additive Manufacturing Research Articles

Effects of Selective Laser Melting Process Parameters on Structural, Mechanical, Tribological and Corrosion Properties of CoCrFeMnNi High Entropy Alloy

AbstractThe structural, tribological, mechanical, corrosion, and other properties of materials produced by laser-based powder bed fusion additive manufacturing methods are significantly affected by production parameters and strategies. Therefore, understanding and controlling the effects of the parameters used in the manufacturing process on the material properties is extremely important for determining optimum production conditions and for saving time and materials. This study aimed to determine the optimal laser parameter values for CoCrFeMnNi high-entropy alloy powders using the selective laser melting (SLM) method. The layer thickness was kept constant during experimentation. 5 different laser powers and 10 varying laser scanning speeds were tested, with hatch spacing from 30 to 90%. After determining the optimal laser parameters for SLM, prismatic samples were fabricated in different build orientations (0°, 45°, and 90°), and subsequently, their structural, mechanical, tribological, and corrosion properties were compared. Melt pool morphology could not be obtained at 20—40 and 60W laser powers and at all laser scanning speeds used at these laser powers. At 100 W laser power, 600 mm/s laser scanning speed, and 70% hatch spacing parameters, an ultimate tensile stress of 550 MPa and elongation of 48% were obtained. Among the samples produced in different build orientations, the sample produced with a 0° build orientation exhibited the highest relative density (99.94%), the highest microhardness (201.2 HV0.1), the lowest friction coefficient (0.7025), and the lowest wear and corrosion rates (0.7875 mpy). Additionally, SLM parameters were evaluated to have a significant impact on the performance of all properties of the samples. Graphical Abstract

Development of Diffraction Research Methodologies for Mediloy S-CO Alloy Speciments Made Using LPBF Additive Manufacturing

Abstract This study focuses on the application and improvement of diffraction measurement methodologies for the optimization of manufacturing parameters of CoCr alloy components made by additive manufacturing (AM) – particularly for Mediloy S-Co alloy specimens made using Laser Powder Bed Fusion (LPBF) additive manufacturing. We measured the phase composition of specimens obtained in AM processes, the measurement of residual stresses resulting from the manufacture of these printed parts, as well as the effectiveness of stress relaxation through the use of heat treatments dedicated to this type of material. Findings reveal several insights into how printing strategies affect the porosity and residual stresses in additive manufacturing. Specimens with higher porosity, particularly those created using specific strategies that resulted in lower energy densities, exhibited lower residual stresses. Notably, printing direction and energy density were found to significantly affect the mechanical stresses within the specimens, with directional choices playing a critical role in the final properties of the parts. Additionally, our findings underscore the complex relationship between various printing parameters and the development of mechanical stresses, highlighting the impact of adjustments in printing strategy on the properties of printed components.

Microstructure evolution and ductility improvement of additively manufactured biodegradable zinc–magnesium alloys via annealing

Zinc–magnesium (Zn–Mg) alloys, fabricated by laser powder bed fusion (LPBF) additive manufacturing techniques, have emerged as promising candidates for biomedical implants due to their biodegradation capability, superior mechanical strength, and excellent biocompatibility. However, LPBF-fabricated Zn–Mg alloys still face challenges related to extremely low ductility and limited exploration of degradation characteristics. In this study, the impact of Mg incorporation on the printability, degradation properties, microstructure, and mechanical properties of LPBF-fabricated Zn–Mg alloys was primarily investigated. Furthermore, we proposed a viable annealing post-processing route for the first time to tailor the microstructural characteristics of the fabricated Zn–Mg alloy and enhanced its limited ductility. The results demonstrated that by applying a laser power of 80 W and a scanning speed of 600 mm/s, the relative density of LPBF-fabricated Zn–Mg alloy reached 98.62%. Increasing the Mg amount from 1 to 5 wt% refined the grain size while promoting an increase in Mg2Zn11 and MgZn2 phases. Among these compositions, the Zn–1Mg alloy exhibited the greatest degradation rate at 0.126 mm/year. The annealing treatment facilitated the microstructure evolution of the Zn–1Mg alloy, resulting in equiaxed grains, increased average grain size, high-angle grain boundaries, and enrichment of Mg at grain boundaries. After annealing at 300°C for 0.5 h, the tensile strength of Zn– 1Mg alloy decreased from 254.92 to 170.93 MPa, while the elongation significantly increased by a factor of 14.3 from 0.55% to 8.43%. These findings provide valuable insights into an effective post-processing approach for tailoring the microstructure and resultant mechanical properties of LPBF-fabricated Zn and its alloys.

Size matters: Exploring part size effects on microstructure, defects, and mechanical property in optimized laser powder bed fusion (L-PBF) additive manufacturing

In laser-based metal additive manufacturing (MAM), effective process optimization requires a thorough analysis of variations across the process window. Despite the common practice of utilizing small-sized coupons to optimize process parameters in laser-based MAM, this study challenges this convention. Through an analysis of microstructure and defect differences in Fe-Ni material parts produced via laser-powder bed fusion (L-PBF), the study reveals significant discrepancies in microstructure, defect and mechanical property based on part size. As part size increases, lack-of-fusion defects and cracks become more pronounced, resulting in a decrease in density from 8.11 g/cm3 to 8.02 g/cm3, leading to constrained grain growth with a decrease of grain size from 41.88 μm to 23.07 μm in the scanning plane. Each defect and microstructural difference was traced back to variations in thermal history based on part size. Finite element method simulations, highlighting differences in thermal history from scanning a single layer to the entire part, showed that an increase in scan length with a widened scan area enlarged the period of the thermal history cycle, leading to considerable cooling. This study underscores crucial considerations for future researchers engaged in process optimization for novel alloy systems using laser-based MAM processes.

Recovery of residual polyamide (PA12) from polymer powder bed fusion additive manufacturing process through a binder jetting process

Purpose This study aims to propose the reuse of PA12 (powder) in another AM process, binder jettiinng, which is less sensitive to the chemical and mechanical degradation of the powder after multiple cycles in the laser system. Design/methodology/approach The experimental process for evaluating the reuse of SLS powders in a subsequent binder jetting process consists of four phases: powder characterization, bonding analysis, mixture testing and mixture characteristics. Analyses were carried out using techniques such as Fourier Transform Infrared Spectroscopy, scanning electron microscopy, thermogravimetric analysis and stress–strain tests for tension and compression. The surface roughness, color, hardness and density of the new mixture were also determined to find physical characteristics. A Taguchi design L8 was used to search for a mixture with the best mechanical strength. Findings The results indicated that the integration of waste powder PA12 with calcium sulfate hemihydrate (CSH) generates appropriate particle distribution with rounded particles of PA12 that improve powder flowability. The micropores observed with less than 60 µm, facilitated binder and infiltrant penetration on 3D parts. The 60/40 (CSH-PA12) mixture with epoxy resin postprocessing was found to be the best-bonded mixture in mechanical testing, rugosity and hardness results. The new CSH-PA12 mixture resulted lighter and stronger than the CSH powder commonly used in binder jetting technology. Originality/value This study adds value to the polymer powder bed fusion process by using its waste in a circular process. The novel reuse of PA12 waste in an established process was achieved in an accessible and economical manner.

High-resolution inherent strain method using actual layer thickness in laser powder bed fusion additive manufacturing with experimental validations

Laser powder bed fusion (LPBF) additive manufacturing (AM) broadens the horizons of design in academia and industry. However, LPBF contends with challenges like residual stresses and distortions due to uneven heating and cooling, leading to substantial resource wastage. Accurately predicting residual stresses and distortions remains a hurdle, primarily due to the need for high-resolution modeling. In this study, a high-resolution model of the inherent strain method (ISM) with actual layer thickness for a cantilever geometry in LPBF is proposed for the first time. Experimental and numerical findings indicate that as the number of layers increases, distortions tend to decrease, while the residual stresses on the top surface consistently remain constant and close to the material's yield stress. The model achieves good agreement (error of 7.1%) for deformation, while the prediction error of residual stresses is reduced from 69% to 32% compared to a traditional ISM model.

Influence of powder surface chemistry on the defect formation in AlSi10Mg alloy processed via laser powder bed fusion additive manufacturing

In laser powder bed fusion(LPBF) additive manufacturing(AM) of Al alloys, surface chemistry and dissolved gas composition(oxygen/oxides/hydroxides, hydrogen and moisture) of AM powders is a major influencing factor for porosity formation. Therefore, in the present investigation, this aspect is addressed using two sets of virgin AM AlSi10Mg powders, namely, Hi-Ox (2770 ppm oxygen) and Lo-Ox (660 ppm oxygen), to assess the printability under various processing parameters and defect formation in printed parts. Comprehensive and in-depth metallurgical analysis of both powders utilizing multiple characterisation techniques established the presence of various types of oxides/hydroxides with different complex chemistries on the powders’ surface. Enhanced spherical gas porosity and oxide inclusions were witnessed in Hi-Ox print coupons in contrast to the least defects in Lo-Ox coupons rationalized due to surface chemistry difference between the virgin powders. Consequently, the mechanical properties of the Hi-Ox print coupons, even with minimum defect density, are significantly inferior to Lo-Ox specimens. These observations suggest a competing influence of surface chemistry/dissolved gas composition and laser parameters for the processing of both powders. Overall, by correlating the microstructures with processing conditions and oxide concentration, defects morphology, the probable melt pool formation mechanism in LPBF of AlSi10Mg alloy (for high and low oxygen concentration) is elucidated.

Laser additive manufacturing of TiB2-modified Cu15Ni8Sn/GH3230 heterogeneous materials: Processability, interfacial microstructure and mechanical performance

Cu/Ni heterogeneous materials integrate excellent thermal conductivity and high-temperature mechanical properties, enabling them to be widely used in the aerospace domain. Differences in the thermal and physical properties of the Cu and Ni materials, however, make them difficult to be processed using the laser powder bed fusion (LPBF) additive manufacturing process. This study systematically examines the effects of various LPBF process parameters on microstructure, element diffusion, bonding strength and microhardness at the Cu/Ni interface, as well as investigating the mechanisms of defect formation within Cu/Ni heterogeneous materials. The results indicate that a reasonable control of laser energy input (< 100 J/mm3) facilitates the Cu/Ni components through strong interfacial metallurgical bonding without pore defect formation. Compared to single-material Cu alloy, the ultimate tensile strength (UTS) of the horizontally bonded Cu/Ni specimen increased by 55.25%, without significant reductions in elongation. The vertically bonded Cu/Ni tensile specimen fractured in the middle of the Cu region rather than the interfacial region, indicating superb interfacial bonding strength. Another advantage lies in the enhancement of thermophysical properties, with a 109.5% increase in thermal conductivity achieved in the LPBF-fabricated Cu/Ni heterogeneous materials compared to the single-material Ni alloy. Quasi-static compression experiments indicated that the Cu/Ni lattice structure could absorb more energy when compressed parallel to the build direction (BD), compared to being perpendicular to the BD. This study provides guidance for the design and manufacture of high-performance Cu/Ni heterogeneous components via LPBF.

A laser powder bed fusion–based methodology for repairing damaged nickel-based turbine blades: Investigation of interfacial characteristics and hot isostatic pressing treatment

This study presents a methodology for repairing a damaged nickel-based turbine blade via laser powder bed fusion (LPBF) additive manufacturing. Specifically, the CM247LC nickel-based alloy was utilized to repair a damaged SRR99 nickel-based blade with LPBF, followed by hot isostatic pressing (HIP) post-treatment. The LPBF repair process achieved crack-free metallurgical bonding at the CM247LC/SRR99 interface with large epitaxially grown grains. Furthermore, HIP facilitated the formation of γ/γ’ phases with comparable dimensions at the interface as well as in the CM247LC and SRR99 regions through recrystallization. Additionally, the columnar grains in the LPBF-printed CM247LC region transformed into coarse equiaxed grains after HIP, accompanied by precipitation of nanoscale Hf-rich carbides. Meanwhile, microcracks in the LPBF-printed CM247LC region and shrinkage pores in the cast SRR99 region were effectively eliminated. The LPBF-printed CM247LC exhibited an 8.62% higher hardness compared to that of SRR99. The repaired samples showed an ultimate tensile strength of 791 MPa, with fracture occurring at the SRR99 side, indicating a reasonable metallurgical bonding strength at the CM247LC/SRR99 interface. The findings offer a novel alternative for the industrial application of repairing damaged nickel-based turbine blades.

Microstructural evolution modelling and low-stress fatigue performance of bimodal-structured Al-Mg-Sc-Zr alloy produced by laser powder bed fusion additive manufacturing

ABSTRACT Coarse – and fine-grained bimodal-structures in a Al-Mg base alloy with rare earth elements of Sc/Zr is produced due to the ultrafast nonequilibrium solidification occurs in laser-induced molten pools during laser powder bed fusion (LPBF) additive manufacturing. A novel high-fidelity cellular automaton (CA) algorithm incorporating numerical calculations of molt-pool temperature fields elucidates the formation and evolution of the bimodal-structure. Subsequent heat treatment induces precipitation of Al3(Sc/Zr) particles within the grains, synergistically enhancing strength and plasticity of the LPBF-processed alloy. The crystal plastic finite element method (CPFEM) is used to reveal the synergistic effect between the strength and plasticity during the material tensile procedure. The bimodal-structure exhibits good fatigue resistance but intriguing anisotropy under low stress cyclic loading. It is proved that differentiated distribution patterns relative to the principal stress direction of the bimodal-structure have a significant influence on its fatigue performance. Numerical evolutionary of the bimodal grain deformation reflects this phenomenon.

A Manufacturability Evaluation of Complex Architectures by Laser Powder Bed Fusion Additive Manufacturing

Abstract Additive manufacturing (AM) enables new possibilities for the design and manufacturing of complex metal architectures. Incorporating lattice structures into complex part geometries can enhance strength-to-weight and surface area-to-volume ratios for valuable components, particularly in industries such as medical devices and aerospace. However, lattice structures and their interconnections may result in unsupported down-skin surfaces, potentially limiting their manufacturability by metal AM technologies, such as laser powder bed fusion (LPBF). This study aimed to examine the correlation between down-skin surface area and the manufacturability of lattice structures fabricated using LPBF. Image processing algorithms were used to analyze down-skin surface areas of seven unique lattice designs and to devise quantitative metrics (such as down-skin surface area, discrete surface count, surface interconnectivity, down-skin ratio, over-print/under-print volumes, etc.) to evaluate LPBF manufacturability. The seven lattice designs were subsequently manufactured using maraging steel via LPBF and then examined using imaging using X-ray micro-computed tomography (XCT). The geometric accuracy of the lattice designs was compared with XCT scans of the manufactured lattices by employing a voxel-based image comparison technique. The results indicated a strong relationship between down-skin surface area, surface interconnectivity, and the manufacturability of a given lattice design. The digital manufacturability evaluation workflow was also applied to a medical device design, further affirming its potential industrial utility for complex geometries.

L-PBF AM process failures causal chain: an FMEA-based monitoring approach for process control

ABSTRACT The laser powder bed fusion (L-PBF) additive manufacturing process offers many advantages. However, its industrial integration still needs to be improved due to the certification constraints of the produced parts. Thus, this paper proposes a phenomenological causal chain of process failures to ensure the control of the L-PBF process and further certify the quality of the parts produced. Consequences of unsuitable thermal regimes are analysed using a failure mode and effects analysis (FMEA) approach, allowing a more global understanding of all the causal chain-related data. The proposed approach is based on standard acquisition equipment available on industrial machines and proves relevant for identifying process failures. Experimental validation of the proposed monitoring method is implemented on a use case using dedicated software. Finally, it is shown that the method is relevant in this confrontation and compatible with the time scale of the process for future NC integration and real-time monitoring.

Qualitative and quantitative characterization of powder bed quality in laser powder-bed fusion additive manufacturing by multi-task learning

Qualitative and quantitative characterization of powder bed quality in laser powder-bed fusion additive manufacturing by multi-task learning

Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior

High porosity level lattice structures made using electron beam powder bed fusion additive manufacturing (EBPBF) need to be sufficiently strong and the understanding of the mechanical anisotropy of the structures is important for the design of orthopedic implants. In this work, the combined effects of loading direction (LD), cell orientation, and strut irregularity associated with EBPBF of Ti6Al4V alloy lattices on the mechanical behavior of the lattices under compressive loading have been studied. Three groups of simple cubic unit cell lattices were EBPBF made, compressively tested, and examined. The three groups were [001]//LD lattices, [011]//LD lattices, and [111]//LD lattices. Simulation has also been conducted. Yield strength (σy-L) values of all lattices determined experimentally have been found to be comparable to the values predicted by simulation; thus, EBPBF surface defects do not affect σy-L. σy-L of [001]//LD lattices is 1.8–2.0 times higher than those of [011]//LD and [111]//LD lattices. The reason for this is shown to be due to the high stress concentrations in non-[001]//LD samples, causing yielding at low loading levels. Furthermore, plastic strain (εp) at ultimate compression strength of [001]//LD samples has been determined to be 4–6 times higher than the values of non-[001]//LD samples. Examining the tested samples has shown cracks more readily propagating from EBPBF micro-notches in non-[001]//LD samples, resulting in low εp.

Role of heterogenous microstructure and deformation behavior in achieving superior strength-ductility synergy in zinc fabricated via laser powder bed fusion

Zinc (Zn) is considered a promising biodegradable metal for implant applications due to its appropriate degradability and favorable osteogenesis properties. In this work, laser powder bed fusion (LPBF) additive manufacturing was employed to fabricate pure Zn with a heterogeneous microstructure and exceptional strength-ductility synergy. An optimized processing window of LPBF was established for printing Zn samples with relative densities greater than 99% using a laser power range of 80 ∼ 90 W and a scanning speed of 900 mm s−1. The Zn sample printed with a power of 80 W at a speed of 900 mm s−1 exhibited a hierarchical heterogeneous microstructure consisting of millimeter-scale molten pool boundaries, micrometer-scale bimodal grains, and nanometer-scale pre-existing dislocations, due to rapid cooling rates and significant thermal gradients formed in the molten pools. The printed sample exhibited the highest ductility of ∼12.1% among all reported LPBF-printed pure Zn to date with appreciable ultimate tensile strength (∼128.7 MPa). Such superior strength-ductility synergy can be attributed to the presence of multiple deformation mechanisms that are primarily governed by heterogeneous deformation-induced hardening resulting from the alternative arrangement of bimodal Zn grains with pre-existing dislocations. Additionally, continuous strain hardening was facilitated through the interactions between deformation twins, grains and dislocations as strain accumulated, further contributing to the superior strength-ductility synergy. These findings provide valuable insights into the deformation behavior and mechanisms underlying exceptional mechanical properties of LPBF-printed Zn and its alloys for implant applications.

Effect of laser focal point position on porosity and melt pool geometry in laser powder bed fusion additive manufacturing

In laser powder bed fusion (PBF-LB) additive manufacturing (AM), the laser beam is the fundamental tool used to selectively melt metal powder layer-upon-layer to form a 3-dimensional part. Studies on the effect of the laser scanning parameters (power, speed, hatch distance, and scanning strategy in general) on part quality are abundant; however, far less emphasis has been given to the effect of the laser beam and how it is focused on the laser-material interaction plane. Here, we have studied the effect of laser beam focal point position on porosity and melt pool geometry in PBF-LB AM. In addition, we also study how the various energy density parameters developed for laser melting processes correlate with melt pool dimensions in a situation where the laser beam focal point position (and the beam diameter and laser intensity change at work plane caused by it), is taken into consideration. Furthermore, we assess the possibility of using co-axial, photodiode-based melt pool monitoring signals as a means to monitor the thermal emissions of the process, and how it correlates with the resulting melt pool geometry. It was found that melt pool penetration experiences a major decrease when the focal point position is shifted by more than ±1 mm (or 30% of Rayleigh length), which could be considered as a tolerance limit for acceptable focus shift in PBF-LB machines. Focus shifts larger than this were effectively captured by the photodiode signals, indicating the potential of using such photodiode-based melt pool monitoring systems for continuous monitoring of focus shift in PBF-LB AM. Finally, it was shown that all the studied energy density parameters, except volumetric energy density, were able to capture the trend in normalized melt pool dimensions when focus position is introduced as a variable. A new energy density metric by normalizing the melt pool monitoring signal intensity with the beam area was introduced and shown to correlate with the normalized melt pool dimensions.

Experimental characterisation of the spreading of polymeric powders in powder bed fusion additive manufacturing process at changing temperature conditions

This study investigates the spreadability behaviour of four different polymeric materials, namely Polyamide 6, Polyamide 6 Black, Polypropylene, and Thermoplastic Polyurethane, under different spreading speeds (30 and 3 mm/s) and powder bed temperatures (25, 80, 110 °C) using a purposely developed experimental apparatus. Macroscopic and microscopic images of the powder layer were taken after completing the powder spreading step. A thresholding-based image processing method was utilised to evaluate the fraction of the bed area not covered by particles (NCF), and the standard deviation of pixel intensities in grayscale images (SDG) was calculated to evaluate powder layer quality in macroscopic images. NCF and SDG can provide quantitative evaluation of the quality of the spread layer, NCF in a logarithmic scale ranking and SDG in a linear scale ranking. A wavelet analysis technique was developed on microscopic panorama images obtained with grazing light to characterise the surface roughness of the layer. Results indicate that the spreadability generally worsens much more significantly than powder flow properties at increasing temperatures and, remarkably, that flowability and spreadability are unrelated. As expected, the temperature effect on powder spreading changes for the different powders are mostly governed by the approach to the powder melting temperature. Minor effects on the final layer quality were also observed at changing spreading speed.

Thermal effects on wear behavior of additively manufactured NiTi shape memory alloys

NiTi alloys fabricated by laser powder bed fusion (LPBF) additive manufacturing technology not only address the compositional instability resulting from complex processes but also solve the challenges of difficult machining of intricate aerospace structures. However, there are very few reports on the wear behavior of LPBF-NiTi alloys. In the present work, the effects of microstructure and thermal treatment, including heat treatment and frictional heat, on the wear behavior of LPBF-NiTi alloy and 100Cr6 ball were analyzed through a series of tribological experiments with different sliding speeds. As the average sliding speed increases (0.079–0.216 m/s), the wear rate of the as-built and heat-treated samples tends to decrease in the range of 2.69 × 10−3–0.97 × 10−3mm3/m. Although the heat-treated LPBF-NiTi alloy is 46 % harder than the as-built alloy is, the latter has a higher toughness (505 MJ/m3) and greater transformation strain of SIM (0.097). This leads to a coupling effect of heat treatment and sliding speed on the wear resistance. In addition, the wear track morphologies under different sliding speeds are asymmetric due to the 24% greater acceleration at the far end from the motor and the 2.15 mm deviation between the maximum speed position and the geometric center of the track. The wear modes of the as-built and heat-treated samples included adhesive, abrasive and delamination wear. Moreover, the wear morphologies and dominant wear modes change with the frictionally caused heat release induced by the sliding speed.

Effect of quenching and tempering treatments on microstructure and mechanical properties of 300M ultra-high strength steel fabricated by laser powder bed fusion

To achieve high-performance 300 M steel parts through the Laser Powder Bed Fusion (LPBF) additive manufacturing process, post-heat treatments are indispensable. Herein, the effects of quenching and tempering treatments on the microstructure and mechanical properties of LPBF-fabricated 300M ultra-high strength steel were investigated, and the relevant strengthening and toughening mechanisms were analyzed. The microstructure of quenched samples primarily consisted of quenched martensite with minor amounts of bainite and some grain boundary allotriomorphic ferrite. The quenched samples presented significantly higher strength than the 300M forgings, primarily attributed to the contributions of solid solution strengthening, grain boundary strengthening and dislocation strengthening. After following tempering treatment, the microstructure of LPBF-fabricated samples mainly consisted of tempered martensite with minor amounts of bainite and residual austenite. Compared to the quenched samples, the tempered samples exhibited a decrease in strength while demonstrating a significant increase in ductility. The samples treated with the optimal heat treatment process (900 °C/1 h/Oil Cooling for quenching + two times of 300 °C/2 h/Air Cooling for tempering) demonstrated a remarkable strength–ductility balance, with a yield strength (YS) of 1834 MPa, an ultimate tensile strength (UTS) of 2099 MPa, and an elongation (EL) of 10.2%, which are all beyond or comparable to those of 300M forgings.

Investigation of melt pool dynamics and solidification microstructures of laser melted Ti-6Al-4V powder using X-ray synchrotron imaging

Titanium alloy (Ti-6Al-4V) is widely used in additive manufacturing (AM) industry. However, as laser powder-bed fusion (PBF-L) additive manufacturing (AM) advances towards reliable production of titanium parts, a thorough understanding of the process-structure-properties (PSP) relationships remain to be fully understood. A study of the laser melting was paired with high-speed X-ray synchrotron imaging at the 32-ID beamline of the Advanced Photon Source at Argonne National Laboratory. Simultaneous melting and imaging was carried out on a Ti-6Al-4V powder layer held in a custom device designed to mimic single-track scans of the PBF-L process at different laser power levels, powder size distributions, and cover gas environments (Ar and He) on top of AM Ti-6Al-4V base metal. It was found that the thickness of the powder layer significantly affected the melt behavior: too much laser powder led to the formation of molten droplets that wetted the surface of the titanium, yet did not contribute to a uniform melting profile. Residual gas pores in the atomized powder were also observed to contribute to the pores observed in the melt pool, with the porosity of the powder (defined as volume of pores divided by total material volume) constant with powder size distribution (i.e., larger particles contained more entrapped gas, which increased final part porosity). When varying Ar or He through the same gas flow meter settings and nozzle, the difference in flow rates likely contributed more to the resultant porosity of the solidified material than did the thermal conductivity of the gasses, with He being the greater contributor to porosity. The microstructure of the heat affected zone contained α′, α, and an increased β phase fraction relative to the base material. The crystallographic texture of the melt pool region adopted that of the base metal.